GTTLINK - NGTTX

Free yourself from the constraints of the factory ECU. 

The Link G4X GTTLink NGTT-X PlugIn fits the Nissan GTT R34 RB25DET NEO. The ECU PCB fits discretely inside the original factory enclosure.

Installation of the Nissan GTT Link ECU is a breeze - no alteration of the factory wiring loom is required. A built-in connector (or pins in some models) provides additional inputs and outputs such as oil pressure inputs or anti-lag / logging switches. 

Most factory features are supported - see Features for any exceptions.

MAP Sensor not included.

This product works with manual transmission vehicles only. 
 
Suitable applications: 

RB20DE NEO, RB25DE NEO and RB25DET NEO in R34 Skylines

RB20DE NEO, RB25DE NEO and RB25DET NEO in C35 Laurels 

RB20DE NEO, RB25DE NEO and RB25DET NEO in Nissan Stageas

- Plus, non neo motors in Stageas 


Need more inputs and outputs? 
The 
XS Expansion Loom offers the ability to add additional inputs & outputs on our range of plug-in ECUs. 

.
 

(215-4000)

Engine Configurations

Engine configurations are pre-set into PlugIn ECUs with a "start" base map.

Limits

  • Engine Temperature Dependent Soft and Hard RPM Limit
  • Engine Temperature Dependent Soft and Hard Boost Limit
  • Vehicle Speed Limit
  • System Voltage Limit
  • User Configurable RPM Limit based on external input

Fueling Adjustments

  • Up to 440 Zone Fuel Table with configurable load and RPM centres. Configurable X and Y Axis Parameters
  • Multiple Fuel Tables
  • Up to 6D Fuel Mapping
  • Injection Rate
  • Master Enrichment
  • Pre Crank Prime
  • Crank Enrichment
  • Post Start Enrichment
  • Warm Up Enrichment
  • Acceleration Enrichment
  • IAT Fuel Correction
  • Injector Deadtime Compensation
  • Overrun Fuel Cut
  • Idle Load Trims
  • Fuel Temperature Correction

Ignition Adjustments

  • Up to 440 Zone Ignition Table with configurable load and RPM centres. Configurable X and Y Axis Parameters
  • Closed Loop Knock Control. (Requires External Controller)
  • Crank Dwell Extension
  • Maximum Advance
  • AFR Table Correction
  • Spark Duration
  • Beginning / End Injection Definable
  • Dwell Time Table. Configurable X and Y Axis Parameters
  • Individual Cylinder Trim
  • Individual Cylinder Tables
  • Multiple Ignition Tables
  • Up to 6D Ignition Mapping
  • Individual Cylinder Ignition Trim
  • IAT Trim
  • Voltage Correction
  • ECT Trim
  • OEM Compatibility
  • CDI Compatibility

Triggering

  • Digital Trigger Decoding
  • Reluctor, Optical Proximity or Hall Sensors
  • Programmable filtering and arming thresholds
  • Configurable trigger patterns or preset triggering options.
  • Supports nearly all OEM trigger patterns and custom trigger arrangements

MotorSport Features

  • Antilag Group A/Group N
  • Launch/Traction Control
  • Flat Shifting
  • Stats Logging
  • Staged Injection

Auxiliary Output Options

  • Application specific. Output drives can be altered from OEM configuration. e.g. Purge control may be in the standard set-up. This can be re-wired and programmed in the Link Plug-in to control intercooler water spray (if added) for example.
    • Each Output independently configurable
    • Unused ignition and injection outputs available as auxiliary outputs
    • General Purpose Output
    • General Purpose PWM
    • Continuously Variable Valve Timing Control
    • Closed Loop Idle Speed Control (Solenoid or Stepper (4 & 6 Terminal))
    • Fuel Pump
    • Fuel Pump Speed Control
    • Engine Fan
    • Air Con Clutch
    • Air Con Fan
    • Intercooler Spray
    • Tacho
    • Check Engine Light
    • Purge Solenoid
    • Oxygen Sensor Heater
    • Switched Cam Solenoid

Variable Valve Timing (where applicable)

  • Up to 4 channel independent
  • Precision Closed Loop Control
  • 3D Tables with configurable X and Y axis controls
  • Preset or Custom Configuration
  • Supported Engines - 1UZFE VVTi; Subaru AVCS; EVO 9 VVT; BMW VANOS; Toyota 3SGE, 1ZZ, IJZ, 2NZ, 2JZ; Honda K20; Nissan VQ35; Ford V8; Holden V6

Processing

  • 40 MHz Specialised Engine Management Microprocessor
  • Ignition control to 0.1 degree, fuel to 0.01 ms
  • 32 Bit Calculation
  • 10 Bit ADC Resolution
  • 20000+ RPM
  • 32Mbit Non Volatile Flash

Inputs/Output

  • Totally application specific
 

Communications

 

  • Tuning Port USB Via Adapter Cable
  • Serial RS232
  • CAN

Analog Inputs

  • Each Channel Independently Configurable With Preset Or Custom Calibrations
  • Wideband O2 (From External Controller)
  • Boost Adjust Signal
  • Configurable Fault Detection Settings
  • Voltage (0-5V)
  • Pyro (From External Controller)
  • Throttle Position
  • Pressure (General Purpose, Fuel, Oil)
  • Air Flow Meter
  • MAP
  • Temperature (Coolant, IAT, General Purpose)
  • Throttle Position
  • Narrow Band O2

Boost Control

  • Engine Temp Correction
  • IAT Correction
  • Multiple Boost Tables
  • External Adjustment
 

Idle Control

  • Reliable And Accurate User Configurable Closed Loop Control
  • Solenoid Or Stepper Motor ISC Valve
  • Aircon, Engine Fan Or Power Steer Idle Up
  • Open Loop Control Mode For Diagnostics

Environment

  • Internal Temperature Range -10 - 85oC
  • Ambient Temperature Range -30 - 90oC
  • Voltage 8 - 22V
  • Operating Current 200mA
  • Electrical Protection On All Inputs And Outputs
 
 

PCLink

  • Adjust ALL Parameters In Real Time
  • Mouse Or Keyboard Operation
  • Tuning
  • QuickTune - Automated Fuel Self Tuning
  • Logging Analysis
  • Diagnostic Information
  • Built In Help
  • Definable Screen Layouts
  • View Over 300 Possible Run Time Parameters

Physical

  • Dimensions And Weights Change According The The Specific Plug-In Supplied
  • Connector : Same As Factory ECU
 

Package Contents

  • G4+ PlugIn ECU
  • MAP Sensor For Applications Where No Factory MAP Sensor Fitted
  • Anti Static Strap
  • Wiring And Installation Instructions

Additional Accessories (Purchased Separately)

  • Intake Air Temperature Sensor

- 3/8 NPT

Suitable applications: 

RB20DE NEO, RB25DE NEO and RB25DET NEO in R34 Skylines

RB20DE NEO, RB25DE NEO and RB25DET NEO in C35 Laurels 

RB20DE NEO, RB25DE NEO and RB25DET NEO in Nissan Stageas

Plus, non neo motors in Stageas

SKU 215-4000
Brand Link ECU
Shipping Weight 0.5000kg
Shipping Width 0.200m
Shipping Height 0.100m
Shipping Length 0.300m
Shipping Cubic 0.006000000m3

Be The First To Review This Product!

Help other Possum Bourne Motorsport users shop smarter by writing reviews for products you have purchased.

Write a product review